Through experiment, investigation, and research the Agri- cultural Experiment Station is constantly discovering new knowledge which is put into teachable form. Tu-Mas; Freshman Varsity Baseball Squad; Varsity Baseball Letter (2, 3, 4); Interfraternity Council; Senior Hat Com mittee Alexander Hunter Gunn III Evanston „„.

• Electronic/Mechanical Thermostat installation and operation manual Model 7-01. • Our Technical Support Group is available from 8 am to 5 pm CST. They may be reached toll-free at 1-888-830-1326. • Important Information. 6 Uninstalling the Existing Unit.

Ovation Celebrity Cc057 Serial Numbers. 9 Installing the Thermostat. 12 Installing the wall plate. 14 connecting the wires. 15 attaching the thermostat. 17 Operation.

20 Indicators & Adjustments. 22 Troubleshooting. Lego Star Wars Ii Nds Rom Download. • Electronic/Mechanical Thermostat Model 40135 Congratulations! Thank you for choosing a Hunter thermostat. Your new Hunter thermostat will provide years of reliable service and year-round energy savings.

Please read this manual before beginning installation and save this booklet for complete operation instructions. • IMPOrTAnT InFOrMATIOn This thermostat is designed to work on the following heating and cooling systems: Gas – Electronic Ignition Gas – Millivolt Systems Electric Air conditioner This thermostat is not designed for heat pump systems or 110/220 V baseboard heating systems.

• TOOlS This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your new thermostat, you will need the following supplies: Flat-head screwdriver Small Phillips-head screwdriver Hammer Electric drill and 3/16” bit Two fresh 1.5 Volt (AA) size alkaline batteries. • Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ensure proper reconnection. • UnInSTAllInG THE ExISTInG UnIT 1.

Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. Remove the existing thermostat cover to access the wires from the wall.

• If your existing thermostat is marked. * See pg 27 for complete wiring diagram. RH / r / Vr / 4 24 Volt 24 Volt Cool rC / VC Y / C* / M air conditioning compressor W / H. • UnInSTAllInG THE ExISTInG UnIT, COnT. Using the provided stickers, label each wire according to the chart. (If the terminals are not labeled, contact a qualified HVAC technician.) note: Wire colors do not always comply with standards, so wire color should be ignored.

Refer to the existing terminal designation for proper identification. • InSTAllInG THE THErMOSTAT InSTAllInG THE THErMOSTAT 1. Remove the new thermostat from the back plate by pulling the two halves apart.

Wall Plate Thermostat. Reposition the wall plate on the wall, pulling the wires through the opening. Insert the mounting screws through the mounting holes and into the anchors. Verify that the thermostat is visually level and securely tighten both screws. InSTAllInG THE WAll PlATE.

• InSTAllInG THE THErMOSTAT, COnT. Loosen, but do not remove, the terminal screws. Note: A jumper wire has been provided, connecting the rC and rH terminals for systems that do not provide both an rH and rC wire. If you have both an rH and rC wire, remove this jumper. • HE/HG Switch. • (The switch has no effect when the system is set to cooling mode.) 5. Insert two fresh AA alkaline batteries.

Align the thermostat with the the wall plate, and snap the two halves together. Restore power at the electrical panel or furnace. • System Switch SYSTEM COOL HEAT AUTO Battery Indicator Switch Thermometer Set Temperature Slider.

Set the temperature. The ystEm mode of the thermostat. The witcH position. To run the fan continuously, slide the note: In operation of your system. In a normal gas or oil furnace, the fan will be turned on by your furnace after its warm-up delay. The second warning is the indicated by the approximately twice every second.